5T Pneumatic Sample Cutting Press (RT-115A)

5T Pneumatic Sample Cutting Press for Rubber, Plastic & Leather Specimens

Product Details:

5T Pneumatic Sample Cutting Press Machine

RT-115A — clean, repeatable dumbbell and tensile specimens from rubber, plastic, leather, film and cardboard

Intro

The RT-115A is an air-driven sample cutting press for laboratories that prepare their own test specimens. A 50 mm cylinder stroke drives a die through sheet material up to 10 mm thick, with cutting force continuously adjustable from 0 to 5T. A four-column guide keeps the platen square to the table. Press Start to bring the die down and hold it under the set pressure; press Stop to release and let the platen return. Beyond specimen preparation, the same machine serves as a compact 5T press for light pressing work.

5T Pneumatic Sample Cutting Press Machine

Feature blocks

Four-column rigid frame Four chromed guide posts carry the moving platen through its full stroke. The die enters the material squarely, which is what makes successive specimens dimensionally identical and extends die life.

0–5T, set to the material A pressure regulating valve gives continuous adjustment across the full range. Thin sheet runs at low force; thick or hard compounds get what they need without crushing the cut edge.

Start and Stop, one button each Press Start to commit the stroke — the platen stays down at the set pressure until you press Stop, which releases and returns it. No button needs to be held through the cut, and a short dwell on thick sheet is simply a matter of waiting a moment before you release.

Compact and mobile Approx. 35 × 35 × 55 cm, approx. 145 kg. Bench-top footprint, no foundation required.

Made to your specimen Standard platen is 250 × 250 × 10 mm; platen size and working table can be built to your drawing, and cutting dies are supplied to match your test standard and material.

Support that gets you cutting Manual plus operation video with every machine, remote walk-through on first start-up, and spare seals available off the shelf.

5T Pneumatic Sample Cutting Press Machine

Specification table

Item Specification
Model RT-115A
Capacity 5T
Pressure adjustment 0–5T, continuously adjustable
Control Start / Stop push-button control
Cylinder stroke 50 mm
Cutting thickness 10 mm
Platen size 250 × 250 × 10 mm
Matched pressure plate Included
Overall size Approx. 35 × 35 × 55 cm
Weight Approx. 145 kg
Power supply 220 V, 50 Hz, 100 W
Working air pressure 0.6 MPa (6 bar)
Air consumption Approx. 0.1 m³/h

5T Pneumatic Sample Cutting Press Machine

Applications

  • Rubber: dumbbell tensile and compression test specimens, aged and unaged compounds
  • Plastic and plastic sheet: tensile and tear specimens, rigid and semi-rigid sheet up to 10 mm
  • Plastic film and flexible packaging: strip and dumbbell specimens without edge tearing
  • Leather and coated fabric: physical test specimens
  • Cardboard, paperboard and corrugated board: die-cut specimens for tensile, bending and thickness testing
  • Composites and other sheet materials that can be cleanly severed by a die
  • General light pressing where a small 5T press is enough

Film and sheet both run on the same press and the same die — only the pressure setting changes.

5T Pneumatic Sample Cutting Press Machine

Service commitments

  • Die matching before shipment: send the drawing, we confirm the die
  • Manual and operation video included
  • Remote commissioning support
  • Spare parts and additional dies available

How to Operate the RT-115A Pneumatic Cutting Press

Place the sheet on the platen and set the cutting die over the specimen area. Dial the working pressure on the regulating valve to suit the material and thickness, anywhere from 0 to 5T. Press Start: the platen comes down and holds the die at that pressure. Press Stop when the cut is through — the pressure releases and the platen returns to its start position.

FAQ

Is this a two-hand control press? No. It uses separate Start and Stop buttons: Start advances the cylinder and holds the platen at the set pressure, Stop releases it and returns the platen. There is no two-hand interlock.

How long does it hold pressure? Until you press Stop — there is no time limit.

Does it work on both film and sheet? Yes. The same press and die handle soft packaging film and rigid or semi-rigid sheet up to 10 mm; only the pressure setting and die clearance change.

Do I need a compressor? Yes, the press is air-driven. Working air pressure and consumption: 0.6 MPa (6 bar)

Can I use my own die? Yes — send the drawing or the standard reference and we confirm the die before shipping.

5T Pneumatic Sample Cutting Press Machine

Send us your material, thickness and specimen drawing. We reply with the die specification and pressure setting within one working day.

Start Earning Substantial Profits In Your Country Today!

RIGHT has helped customers in more than 100 countries to be successful and earn good profits. We also welcome you to become an exclusive distributor in your country.

After signing the agreement, we will not wholesale any more products to your country or region, your orders will be processed and shipped first, and we will execute your custom machine design after you send us the first time. Click the buttons below, and let’s grow your brand together.

RIGHT's Services Always Go Extra Mile

No more endlessly wasting time on other lousy suppliers. RIGHT's goal is to let you sit back and relax. We take care of all the dirty works, including trade stuff, clearance and logistics, etc. Our consultant will keep you informed of the trade progress throughout.

Product Categories
5T Pneumatic Sample Cutting Press (RT-115A)

Ask For A Quick Quote

We will contact you within 1 working day, please pay attention to the email sales@dgright.com

Get In Touch

Fill in the form below and our team will be happy to assist you

Contact Information

+86 769 2288 2009 
dgright@righttester.com

Opening Hours

Monday – Friday 9am-5pm 
Weekend – Closed

Address

Wentang, DongCheng District 523000, Dongguan City, Guangdong Province, PR China